News Archive

"Early Spring Special" CASHBACK PROGRAM (UK & EUROPE)

Extended and Updated "DR-2X Installation Support Program”

Extended and Updated "DR-2X Installation Support Program”

including free LAN-01A unit!

If you own a DR-1XE in working conditions and you are willing to switch to the DR-2XE you can trade your old digital repeater in and get an additional € 300.00 cashback.

1'099 .- CHF (inkl. 300.00 Euro Cashback)

Der Kauf muss zwischen den 01/01/2019 und 30/06/2019 erfolgen.

Erste FTDX101D Probe !!!

YAESU Portable Digital Node Function

We are excited to announce that firmware update for the FT2DR/E along with the latest WiRES-X PC Software (V1.50) has been released on the official website ( This update will enable the FT2DR/E to work as a WiRES-X Portable Node Station with the following firmware and the WiRES-X software:

  • FT2D MAIN FW V3.10
  • FT2D DSP FW V4.31
  • WiRES-X PC Software V1.50

To set up a Portable Digital Node Station with the FT2DR/E, the SCU-39 WiRES-X connection cable kit accessory is required. The SCU-39 will be available very soon.

Users can easily establish and operate a WiRES-X Portable Node Station by directly connecting the FT2DR/E to the PC with the SCU-39. The conventional HRI-200 internet interface kit is not required for the Portable Digital Node function, and no fixed global IP address is necessary. Since users do not need to open an Ethernet port, the WiRES-X communication from any location is possible - such as Hotel rooms, Airports, Vehicle Wi-Fi, or even Wi-Fi Access Points.

With the new Portable Digital Node Function, users can gain access to WiRES-X Network directly by using the USB connected FT2DR/E with the radios PTT and microphone. The need to have an additional radio to talk to a node radio is no longer needed in order to enjoy the WiRES-X Network. The USB connected FT2DR/E can also function as an Access Point for RF communication. Four different types of operation modes are available. For more information, please refer to the operation manual which is posted on the official website (

Exciting new features of WiRES-X PC Software (V1.50) includes the following two updates:

  • Sub-code Function: When selecting DG-ID ‘00’ in the WiRES-X software (under the transceiver settings) you can select a Sub-code from “00” to “26”. When the DG-ID and sub-code are set to “00,” the node relays C4FM digital signals of all DG-ID numbers. When a sub-code is set with a value of “01” – “26,” the node relays C4FM digital signals with the subcode that is matched. This will allow multiple open nodes (DG-ID ‘00’) to work within the same communication range; this function is useful to avoid interference between nodes.
  • Digital Only Room: A Digital Room can be set up if desired with the WiRES-X PC Software V1.50 (Note: The HRI-200 is needed in order to create a room.)

With the Portable Digital Node function, the flexibility and mobility of the WiRES-X Network will be available all the time. Firmware updates will be released soon that will make it possible for the FTM-400XDR and FTM- 100DR transceivers to function as a Portable Digital Node. We believe that this new WiRES-X functionality will contribute to the growth of the YAESU C4FM (System Fusion) network and expand your business opportunities with the YAESU C4FM transceivers.

Neu ab jetzt: 5 Jahre Garantie auf alle neuen YAESU Produkte!!!

Nur bei GIANORA-HSU !!!

ExpertRC 1.3.0 RC and ExpertRS 0.6.4;%20ExpertRS%200.6.4%20Release%20Notes.pdf


Main Features release schedule*:

January 2018

  • Design update, similar to what has been done to ExpertRC
  • VAC (voice data transfer) implemented in TCI, for digital modes operation

February 2019

  • New Antenna Switch
  • New ExctCtrl/PA tab
  • Transverter mode

March/April 2019

  • ALC
  • New IQ Player module
  • New RX module (similar to PROC module for TX)
  • Manual TNF

Summer 2019

  • Full Duplex
  • Predistortion

*Release schedule may be changed in time


New Adapters & Connectors !!!